N 10 20 30 50 100 200 300 500 Isf-F500
Suitable for measuring weight and tensile forces
N 10 20 30 50 100 200 300 500 Isf-F500
Suitable for measuring weight and tensile forces
N 10 20 30 50 100 200 300 500 Isf-F500
Suitable for measuring weight and tensile forces
Scale / Crane Scale
Zero-setting, weighing, subtracting tare value LCD display, with backlight Automatic power off Unit: kg
Código Isu-100D Piezas Fundidas Y De Aluminio
Can measure rotary speed, line speed and line length Automatically save the maximum value, minimum value and the last value, 96 data can be stored during
Multímetro Digital (Con Clavija Indicadora Con Luz)
Jack indicator light: jacks flash green to indicate the corresponding jacks for test leads NCV detection and judge the strength by light and buzzer True RMS mea
6Mω/60Mω 0.001Mω/0.01Mω ±(1.5%+3)
Automatically identify test modes for AC voltage/DC voltage/resistance/continuity NCV detection and judge the strength by light and buzzer Self-calibration when
Detector De Fase Y Tensión De Ca Comprobador De Voltaje Digital
Non-contact detection of phase sequence, high and low voltage, wire distinction Low battery indication Auto power off Flashlight
Cámara Térmica De Bolsillo Salida Ip54
Tester tip: CRV materia
Detector De Fase Y Tensión De Ca Comprobador De Voltaje Digital
Non-contact detection of phase sequence, high and low voltage, wire distinction Low battery indication Auto power off Flashlight
Trabajo -5°C ~ 50°C Absoluto Fondo Parte Inferior Está Hacia Arriba Bottom Absoluto
Used as level and slope meter Aluminum frame Magnetic bottom The display flips over when the bottom faces up The backlight is on automatically when in use, and
Esfera Medidora De Cerámica
Buttons: on/off, hold (keep the reading), zero, ABS (absolute and incremental measurement) Fix the locking screw at 4 positions for different measuring ranges:
Trabajo -5°C ~ 50°C Absoluto Fondo Parte Inferior Está Hacia Arriba Bottom Absoluto
IP54 dust/waterproof Used as level and slope meter Aluminum frame Magnetic bottom with V-groove for shafts The sea level is permanently set inside the chip, zer
Cal. Dig. De Simetría De Ranuras
opcional: cable salida de datos medir la profundidad (código 7315-50M se necesita receptor, 7302-40M) del chavetero Código Rango Resolución Precisión 2182-25 0-
Medidor De Radio Digital (Baja Precisión)
Measure radius of external arc, arc angle of measured surface should be larger than 60° Display radius value, no need to calculate Button function: on/off, zero
Medidor De Radio Digital (Baja Precisión)
Measure radius of external arc, arc angle of measured surface should be larger than 60° Display radius value, no need to calculate Button function: on/off, zero
Medidor De Radio Digital (Baja Precisión)
Measure radius of external arc, arc angle of measured surface should be larger than 60° Display radius value, no need to calculate Button function: on/off, zero
Medidor De Radio Digital (Baja Precisión)
Measure radius of external arc, arc angle of measured surface should be larger than 60° Display radius value, no need to calculate Button function: on/off, zero
Fondo Magnético Parte Inferior Está Hacia Arriba
Used as level and slope meter Aluminum frame Magnetic bottom The display flips over when the bottom faces up The backlight is on automatically when in use, and
Alarma Acústica Cuando La Pantalla Se Voltea Cuando La
Single axis/double axis level and slope meter, gyro technique can measure the angle between two planes in any direction Hard plastic case, with V-shaped grooves
Set De Escuadras Combinadas (Transportador Cerrado)
Square head (made of zinc): set the blade at 90° or 45° to an edge of a workpieceaccuracy: ±0.5° Blade (made of stainless steel): range: 300mm/12", g
Set De Escuadras Combinadas (Transportador Cerrado)
Center head (made of cast iron): to locate center of cylinders with diameter (Ød): 30-100mm, accuracy: ±0.15mm Protractor head (made of cast iron): set the blad
Set De Escuadras Combinadas (Transportador Cerrado)
Center head (made of cast iron): to locate center of cylinders with diameter (Ød): 30-100mm, accuracy: ±0.15mm Protractor head (made of cast iron): set the blad
90° Escuadras De Bordes Planos Con Base Ancha
Graduation: 1mm Aluminum blade and base 4 milled surfaces Retractable metal ledge support Etchings and holes for beveling and framing: 10°, 15°, 22.5°, 30°, 45°
